| Last Modified: 11-29-2007 | 1.6 A | |
| Service Category: Vehicle Interior | Section: Meter/Gauge/Display | |
| Model Year: 2008 | Model: Sequoia | Doc ID: RM000002YKH002X |
| Title: METER / GAUGE / DISPLAY: ACCESSORY METER: REMOVAL (2008 Sequoia) | ||
REMOVAL
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing
.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected
.
2. REMOVE LOWER NO. 2 STEERING WHEEL COVER
3. REMOVE LOWER NO. 3 STEERING WHEEL COVER
4. REMOVE STEERING PAD
5. REMOVE STEERING WHEEL ASSEMBLY
6. REMOVE LOWER STEERING COLUMN COVER
7. REMOVE UPPER STEERING COLUMN COVER
8. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
9. REMOVE FRONT DOOR SCUFF PLATE LH
10. REMOVE COWL SIDE TRIM BOARD LH
11. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
12. REMOVE FRONT PILLAR GARNISH LH
13. REMOVE INSTRUMENT SIDE PANEL LH
14. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
15. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH
16. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
17. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY
18. REMOVE REAR CONSOLE BOX POCKET
19. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
20. REMOVE CONSOLE BOX CARPET
21. REMOVE REAR CONSOLE BOX ASSEMBLY
22. REMOVE FRONT CONSOLE BOX
23. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
24. REMOVE COMBINATION METER ASSEMBLY
25. REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL
26. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY
27. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)
28. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
29. REMOVE INSTRUMENT SIDE PANEL RH
30. REMOVE FRONT DOOR SCUFF PLATE RH
31. REMOVE COWL SIDE TRIM BOARD RH
32. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
33. REMOVE FRONT PILLAR GARNISH RH
34. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
35. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH
36. REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY
37. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
38. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY LH
39. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
40. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY RH
41. REMOVE NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
42. REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (for 14 Speakers)
43. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD INSERT
44. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for 14 Speakers)
45. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for 8 Speakers)
46. REMOVE NO. 3 INSTRUMENT PANEL STAY
47. REMOVE GLOVE BOX LIGHT ASSEMBLY
48. REMOVE NO. 1 HEATER TO REGISTER DUCT
49. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT
50. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT
51. REMOVE DEFROSTER NOZZLE ASSEMBLY
52. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
53. REMOVE ACCESSORY METER ASSEMBLY
(a) Disconnect the connector.
|
(b) Remove the 3 screws and remove the accessory meter assembly. |
|
|